Micromachining of 316LVM stainless steel tubes using periodic acousto-optic modulation of pulsed Nd:YAG lasers for cardiovascular stent applications

S. K. Sudheer; V. P. Mahadevan Pillai; V. Unnikrishnan Nayar; Yavar Pothiawala; Devesh Kothwala; Dhiraj Lal Kotadia

doi:10.1117/1.2201038

1 April 2006 Micromachining of 316LVM stainless steel tubes using periodic acousto-optic modulation of pulsed Nd:YAG lasers for cardiovascular stent applications

S. K. Sudheer, V. P. Mahadevan Pillai, V. Unnikrishnan Nayar, Yavar Pothiawala, Devesh Kothwala, Dhiraj Lal Kotadia

Author Affiliations +

Journal of Micro/Nanolithography, MEMS, and MOEMS, Vol. 5, Issue 2, 023010 (April 2006). https://doi.org/10.1117/1.2201038

Abstract

Optoelectronic techniques can be used in laser applications in biomedical instrumentation to achieve better flexibility and control of the available optical power. These techniques enable the processing and manufacturing of biomedical implants like cardiovascular stents and micrometallic components with reduced heat-affected zone (HAZ) and extremely precise edge cutting. The present investigations deal with the study of laser piercing routines and further profile cutting of thin stainless steel sheet tubes for biomedical implant manufacturing. The process is performed using an acousto-optic (AO) modulator-based pulsed Nd:YAG laser. The AO modulator used in the experiments is a Bragg diffraction device. During the piercing of holes, the focused laser power is gradually increased from a low value and finally reaches the maximum as the beam goes deeper into the material. The most suitable value of dwell time is found to be 50 ms. A nine step staircase modulating voltage with a maximum ac component of 800 mV is used, and the laser power is 4 W in TEM00 operation. The acousto-optic modulator-based pulsed Nd:YAG laser is capable of cutting extremely complex geometries of stents on 316LVM tubing. Laser cutting results in a kerf width of 20.5±0.5 µm. Precise strut dimensions of 115±15 µm for subsidiary strut, 150±15 µm for main strut, and 150±15 µm for the link are also obtained. With the piercing routine, extremely fine holes with reduced heat-affected zones are produced, and this quality is reflected during consequent machining of required profiles for implants.

©(2006) Society of Photo-Optical Instrumentation Engineers (SPIE)

Citation Download Citation

S. K. Sudheer, V. P. Mahadevan Pillai, V. Unnikrishnan Nayar, Yavar Pothiawala, Devesh Kothwala, and Dhiraj Lal Kotadia "Micromachining of 316LVM stainless steel tubes using periodic acousto-optic modulation of pulsed Nd:YAG lasers for cardiovascular stent applications," Journal of Micro/Nanolithography, MEMS, and MOEMS 5(2), 023010 (1 April 2006). https://doi.org/10.1117/1.2201038

Published: 1 April 2006

ACCESS THE FULL ARTICLE

INSTITUTIONAL
Select your institution to access the SPIE Digital Library.

SELECT YOUR INSTITUTION

PERSONAL
Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.

PERSONAL SIGN IN

No SPIE Account? Create one

PURCHASE THIS CONTENT

SUBSCRIBE TO DIGITAL LIBRARY

50 downloads per 1-year subscription

Members: $195

Non-members: $335 ADD TO CART

25 downloads per 1 - year subscription

Members: $145

Non-members: $250 ADD TO CART

PURCHASE SINGLE ARTICLE

Includes PDF, HTML & Video, when available