This work reports results of laser beam profile measurements, performed for earlier on designed and successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow-GeO2-doped-ring core (HRC). We compared two drawn from the same preform HRC MOF samples without and with induced during the drawing process twisting of 790 revolutions per meter. Researched silica HRC MOF with outer diameter 65 µm contains hollow ring-core inner diameter of 30.5 µm with wall thickness of 1.7 µm and refractive index difference Δn = 0.03; 90 air holes, placed over typical hexagonal geometry in the periphery domain from the outside HRC at the distance 14 µm, with hole averaged diameter 2.5 µm and pitch 7.5 µm. According to simulation results (mode analysis, performed by rigorous finite element method via commercially available software COMSOL Multiphysics®), it supports two guided LP-modes (fundamental LP01 and the first higher-order LP11) or 4 HE/EH odd and even eigenmodes – HE11/EH11 and HE21/EH21, respectively. We present some results of laser beam profile measurements, performed under various launching conditions (different laser sources as well as excited optical fibers (both commercially available single-mode optical fiber of ITU-T Rec. G.652 and multimode optical fiber 50/125 of ISO/IEC Cat. OM2+/OM3)) at the output ends of researched HRC MOF twisted and untwisted samples as well as at the output end of large core multimode optical fiber 100/125, aligned with excited HRC MOF.
This article is devoted to the generation of surface plasmon at the interface “graphene coating – quartz glass”, as well as on the surface of a round conducting particle. Such plasmons are of interest for creating sensor devices in medicine and biology due to the neutrality of graphene coatings. It is said that to increase the sensitivity of the sensor, the plasmon should be amplified. It has also been shown that the presence of conductive particles in the substance under study affects the overall refractive index of the substance and changes it even at the most insignificant concentration of additional substances (analytes).
The paper proposes a conversion method «ILCF-to-amplitude» based on an erbium fiber-optic amplifier. The main design parameters of the conversion device are estimated. It is proposed to select the parameters of the erbium medium in such a way as to obtain the largest steepness of the amplifying characteristic of the converter in the region of the operating wavelength of the segment radiation. On the basis of the stationary model of signal conversion processes in EDFA the basic parameters of the converter are obtained, after which their refinement is performed. Using a specialized simulator, the transfer function of the proposed converter and the possible noise level in the system are determined.
KEYWORDS: Radio optics, Pulse signals, Telecommunications, Unmanned aerial vehicles, Fiber optics, Signal processing, Control systems, Waveguides, Telecommunication networks, Radio over Fiber
The article is devoted to the consideration of the possibility of using the chirp function of optical pulses as a resource for radio segment control in RoF-systems. Such a resource does not belong to the traditional telecommunication resource, is realized at the physical level and is characterized by high speed. The scheme of RoF-segment construction is proposed - using the developed components: the converter «Chirp To Amplitude» and interference splitter. In the case when the antenna array forms a spatial separation of VLANs, it is shown that the parameter of payload of device interfaces improves in relation to the VLANs traditionally formed on the radio segment.
Orthogonal Frequency Division Multiplexing (OFDM) technology1 has found wide application in optical communication systems due to its efficient use of available bandwidth, absence of intersymbol interference, and mitigation of dispersion and nonlinearity effects in the optical channel. However, OFDM has several drawbacks, the key one is the problem of high peak-to-average power ratio (PAPR)2 . In optical transmission systems3 , this becomes particularly relevant as it leads to nonlinear distortions caused not only by power amplifiers but also by LED emitters, thereby reducing the efficiency of converting light into communication and significantly impacting the lifespan of the LED and laser diode. This paper describes a new PAPR reduction method based on the application of the Kronecker product in the transmitter and receiver matrices formation in asymmetrically-clipped optical OFDM. It is applied in the transmitter side by the Kronecker product of the IFFT matrix and the data matrix, and then in the receiver by the Kronecker product of the FFT matrix and the channel matrix. Creating these matrices can distribute the signal power across all subcarriers and maintain orthogonality, thereby contributing to reducing the peak-factor. Numerical experiments were conducted to evaluate the effectiveness of the method. Simulation results show that this approach can reduce the peak-factor value by 2.3%. Overall, the developed method based on the Kronecker product provides a promising solution for reducing PAPR in OFDM optical systems and can be used to improve the performance and efficiency of data transmission in optical communication systems, moreover, this signal undergoes further transformation - the formation of quasi-orthogonal multiplexing methods for transmission on the air network.
The article discusses the optoelectronic properties of the new poly[2-ethyl-3-methylindole]. Samples of phototransistors were obtained in which thin films of polyindole were used as a transport layer, their characteristics were measured and analyzed under the influence of ultraviolet radiation with a wavelength of 350 nm. Organic field-effect transistors based on synthesized pyrrolidinofullerenes have also been created. The family of output characteristics for pyrrolidinofullene and polyindole was determined. The mobility of charge carriers in thin films of polyindole and pyrrolidinofullerene has been estimated. The kinetics of the current photoresponse in transistors based on polyindole and pyrrolidinofullerene films has been studied.
KEYWORDS: Holography, Data transmission, Holograms, Image transmission, Signal to noise ratio, Data communications, Image compression, Digital holography, Mobile communications, Modulation
The article discusses the problem of reducing the transmission speed of images and any other digital data in mobile networks when errors occur. The decrease in speed is explained by a different approach to the issue of data transmission quality in communication networks and in IP networks - if in communication networks a very small, but non-zero probability of error is acceptable, then in IP networks the TCP protocol ensures guaranteed delivery, and the data packet is delivered either without errors, or a connection failure is detected. The solution to the problem is to increase the noise immunity of the communication channel and reduce the probability of error at the decoder output to 0.000001. This requires a method of noise-resistant coding with a much greater correction capacity compared to the known codes used in communication networks. This method is the holographic coding method. When using it, the average speed of information transmission increases, the load on channels with retransmitted packets decreases, and freeing up channels will make it possible to do without additional frequency resources and an increase in the number of base stations. To ensure that the redundancy of the holographic code does not reduce the transmission speed in channels with good communication quality, it must be turned on only in those channels where a drop in speed of more than 10 times is recorded.
The article is devoted to the problems of modern communications, namely – to custom experimental fibers that be used in future communication systems. We consider a non-standard optical fiber which, due to its structure, offers an advantage in multi-channel transmission via different modes. This fiber has a hollow-core structure which means that traditional light coupling methods can be not efficient. In the experimental part, the conductivity of the fiber tested by finding a solution to improve the radiation coupling into the fiber. The conclusion presents the final with the experimental results and summarizes the topic of the paper.
KEYWORDS: Modulation, Orthogonal frequency division multiplexing, Radio over Fiber, Signal processing, Energy efficiency, Phase shift keying, Quadrature amplitude modulation, Optical fibers, Interference (communication), Distortion
Future 6G networks will be able to support a wide range of services with different technical requirements and in different frequency bands. To achieve this goal, the use of radio over fiber (RoF) technology is an important foundation for both the transport architecture and the hybrid radio-optical centralized architecture or 6G fronthaul cloud radio access network (CRAN). At the same time, the 6G generated signal processing technologies and modulation schemes must meet the stringent requirements of a mobile data network. In this paper we estimate energy efficiency of DFT-s-OFDM in RoF systems in terms of peak-to-average power ratio (PAPR).
KEYWORDS: Orthogonal frequency division multiplexing, Signal filtering, Modulation, Fourier transforms, Energy efficiency, Signal processing, Optical filters, Electronic filtering
This article proposes a method for improving energy efficiency by reducing the peak power of the emitted signal in systems with DFT-s-OFDM for fiber-optic segments of future mobile networks of the 5G and 6G generation, based on the use of an improved "raised cosine" shaping filter, as well as ZT-DFT-s-OFDM technology for improved energy efficiency. Various new waveforms and modulation schemes are presented that would be both energetically and spectrally efficient. The analysis of the ratio of the peak signal power level to the average level for signals with DFT-s-OFDM in its various modifications in radio-optic networks is presented, various technologies for the formation of DFT-s-OFDM are analyzed depending on the method of access to the subscriber, such as DFDMA, LFDMA and IFDMA, considering the bandwidth extension factor.
In this article we present the results of an experimental study of a periodically poled lithium niobite (PPLN) crystal designed to generate sub-terahertz radiation based on the process of difference frequency generation using two optical carriers of close frequencies. This crystal was specially designed for this frequency range. The resulting generation efficiency turned out to be relatively low, however, here we present the proof of concept.
The article is devoted to the study of issues related to the developments of methods for manufacturing 3D refractive index profiled fiber and fiber-compatible structures. Based on the results of the analysis of published works, it was established that there are no tested approaches with generality to solving this problem. Therefore, the method proposed by the authors seems relevant, which can be classified as a technique for bulk transformation of material properties, which makes it possible to approximately select, and then adjust (with refinement) the volumetric refractive index profile of the selected area to the simulated value. In this article, the authors present the results of the formation of a guiding structure along the boundary of a profiled area. The method of three-beam UV burning and the method of focused ion burning were studied. It has been found that in the second case, significant differences in the refractive index can be obtained. Therefore, the second method may be of interest for the manufacture of large-sized components.
The article discusses the possibilities of using holography for parallel transmission of information in communication channels. Existing channels use serial transmission. At the same time, there is an effect that can be considered as a parallel transmission of information – holography. To transmit a hologram over a communication channel, it is necessary to transpose the space-time matrix. In this case, the information is deployed in space, and two local points are used in time – the moment of the formation of the object and the moment of the formation of the hologram. One option is optical holography, where an array of lasers pointed at the receiver matrix forms an interference pattern on it. The second option is the use of radio holography, the third is the transfer of the communication channel from the space-time domain to the time-frequency domain. To do this, one can use the transfer of the information block into a linear array of the spectrum in the frequency domain (time-frequency transposition). In this case, the hologram is aligned in the frequency space – the shape of the hologram corresponding to the transmitted information block contains the signal spectrum. The approaches considered are a problem statement for developing methods for parallel holographic transmission and creating communication channels that practically do not have an upper bandwidth limit. The theoretical limit is the transmission rate of a hologram – the amount of information contained in a three-dimensional image of a complex object, within the duration of one period of an electromagnetic wave.
This work presents results of test series, performed for earlier on designed and successfully fabricated twisted silica fewmode microstructured optical fibers (MOF) with six GeO2-doped cores. While Part I introduces results of differential mode delay map measurements, Part II is focused on researches of spectral responses, measured for fiber Bragg gratings, recorded in these multi-core MOFs with core graded refractive index profiles and induced twisting 100 revolutions per meter. Specially setup for spectral response measurement for described complicated fiber optic element was developed, that provides selected alignment of matching singlemode optical fiber with particular single core of MOF via free space and reducing of reflection by precision 8 angle cleaving. Comparing analysis of measured spectral responses confirmed written FBGs in 2 of 6 cores, and demonstrated potentiality of fabricated complicated structure, containing multi-core MOF with FBG, for applications in multichannel fiber optic sensors with spatial division multiplexing technique.
This work presents some results of pulse and spectral responses, performed for laser-excited pilot sample of earlier on designed and fabricated chiral silica few-mode optical fiber (FMF) with induced twisting 66 revolutions per meter (rpm), typical (for telecommunication optical fibers) cladding diameter 125 μm, weakly increased core diameter up to 11 μm and numerical aperture NA=0.22, corresponding to improved height of quasi-step refractive index profile. Described FMF 11/125 provides propagation of 4 and 6 guided modes over “C” and “O”-bands, respectively. We present results of tests, focused on researches of few-mode effects, occurring under laser-excited optical signal propagation over pilot sample optical fiber, and their influence on pulse and spectral responses, including some measurements, performed for fiber Bragg grating, recorded in tested FMF 11/125.
In this article the principle of instrumental (experimental) determination of the parameters of mode compositions of an optical signal propagating along an optical fiber is described. The measurement scheme is based on the use of a wellknown experimental setup designed to obtain the profile of the refractive index of an optical fiber. In addition to that setup, it is proposed to perform measurements for different angular positions of the investigated optical fiber, and for its different longitudinal positions. The proposed method is realizable in the case when the signal propagating through the optical fiber is characterized by increased intensity, which makes it possible to measure a nonlinear (Kerr) caused addition to the refractive index. It is proposed to calculate the desired mode weight coefficients by the method of probabilistic selection according to the developed method.
In this paper we present an effective and simple method of image compression based on spectral analysis rather than redundancy reduction. A significant portion of traffic transmitted over communication channels is static and dynamic images, and the volume of this traffic is growing at a faster rate than the capacity of communication channels is increasing. One of the ways to solve this problem is to compress the transmitted images. Data compression can be done in two ways – with and without loss of information. A distinctive feature of images as a form of information presentation is the presence of large internal redundancy, which allows the use of lossy compression methods. To exclude the loss of meaningful information, it is necessary to take into account the specifics of specific signals and divide them into groups according to the predominant concentration of information in the frequency or in spatial domain. To do this, one can use the analysis of the spatial spectrum of images and remove some part of the spectrum with an acceptable loss of information.
This work reports the results of bandwidth measurements and tests, performed for earlier on designed and fabricated pilot lengths of new silica laser-optimized graded-index multimode fibers (LOMFs) with extremely enlarged core diameter up to 100 μm and "typical" "telecommunication" cladding diameter 125 μm. Presented optical fibers are targeted for harsh environment short-range multi-Gigabit onboard cable systems and industrial networks. Proposed LOMF 100/125 differs by specially optimized graded refractive index profile, that provides low differential mode delay (DMD) for selected guided modes. We present some results of tests, performed for fabricated pilot 520 m length of described LOMF 100/125, focused on researches of bandwidth features. They contain DMD map and transfer function measurement as well as 10GBase-LX/SX channels eye-diagram and bit-error-ratio reports with following direct detection of the maximal acceptable optical fiber length for guaranteed 10Gbps channel supporting.
Twisted fibers provide interesting properties in terms of mode coupling relevant for optical multichannel systems. In this regard, the article provides an overview of the use of space division multiplexing (SDM) technology in radio over fiber data transmission systems in future high-speed scalable 6G wireless networks. The features of using the SDM technology in the radio access network are analyzed. The application of new specialized few-mode fibers in 6G networks for useful information transmission is proposed. The results of experimental and simulation studies of custom twisted (chiral) optical fibers designed for vortex mode generation/maintenance are also presented, which can be used as a basis for hybrid modulation development, using both temporal and spatial properties of the signal.
In this paper we present a brief analysis of existing materials and structures with quadratic-nonlinear optical properties that can be used to generate a difference frequency in both THz and sub-THz frequency ranges. This task is actual for future hybrid radio-over-fiber systems exploiting ultra high frequencies (6G etc.). It is shown that such a device may be of interest regarding the problems of generating (preparation) quantum-entangled states of photons, which can find application in high-performance computing and information systems. It is shown that the proposed concept of nonlinear optical-to-radio converter can be applied for entangled photons preparation as well.
KEYWORDS: Modulation, Orthogonal frequency division multiplexing, Signal processing, Radio over Fiber, Filtering (signal processing), Radio optics, Quadrature amplitude modulation, Networks, Electronic filtering, Frequency division multiplexing
6G mobile networks will support a wide range of services with different technical requirements and in different frequency bands. To achieve this goal, the use of radio-over-fiber (RoF) technology together with optical space division multiplexing (SDM) technology is an important basis for creating both a transport architecture and a hybrid radio-optical centralized architecture or cloud radio access network (C-RAN) 6G fronthaul. At the same time, the 6G signals processing technologies and the modulation schemes must meet the stringent requirements for a mobile data transmission network. The paper presents a study and simulation results of the process of signal conversion and retransmission with a promising data processing technology – DFT-s-OFDM with rotated QAM modulation over a fiber-optic line using RoF technology; a numerical estimation of PAPR level is also given.
The paper discusses a method of error-correcting coding based on the transfer of holographic coding of an arbitrary digital signal into the spectral range. The process of coding a code message consists in generating N radio pulses at orthogonal frequencies (a set of frequencies is determined by a holographic encoder for each message) by switching the outputs of N harmonic signal generators operating in a constant mode. The group signal is formed by summing the manipulated harmonics at the input of the transmitter amplifier or directly in the antenna. Signal decoding in the receiver is performed by calculating the spectrum of the received signal and applying an inverse holographic transform to it, which restores the value of the transmitted data block. Spectral holographic coding provides a 7-8 dB gain in noise immunity compared to coding the signal itself. Another advantage of the spectral code is the lower complexity of encoding and decoding when the redundancy is changed over a wide range, as well as high secrecy due to the use of a noise-like signal.
In this paper the chiral fiber Bragg gratings (ChFBG) for generation of fiber modes carrying orbital angular momentum (OAM, vortex modes) are considered. Within the framework of the article, a generalized mathematical model of ChFBG is presented including an arbitrary function of apodization and chirping, which makes it possible to calculate gratings that form vortex modes of a given order for the required frequency range with the required reflection coefficient. In addition, a matrix method based on the mathematical apparatus of the coupled modes theory for describing ChFBG is proposed, simulation of the considered fiber structures is carried out.
In this article the principle of instrumental (experimental) determination of the parameters of mode compositions of an optical signal propagating along an optical fiber is described. The measurement scheme is based on the use of a wellknown experimental setup designed to obtain the profile of the refractive index of an optical fiber. In addition to that setup, it is proposed to perform measurements for different angular positions of the investigated optical fiber, and for its different longitudinal positions. The proposed method is realizable in the case when the signal propagating through the optical fiber is characterized by increased intensity, which makes it possible to measure a nonlinear (Kerr) caused addition to the refractive index. It is proposed to calculate the desired mode weight coefficients by the method of probabilistic selection according to the developed method.
The article provides an overview of the use of space division multiplexing (SDM) technology in radio-over-fiber (RoF) data transmission systems in future high-speed scalable 6G wireless networks. The features of using the SDM technology in the radio access network are analyzed. The application of new specialized few-mode fibers in 6G networks for the useful information transmission is proposed. The results of experimental studies of custom optical fibers designed for vortex mode generation are also presented.
KEYWORDS: Signal generators, Radio optics, Radio over Fiber, Antennas, Modulation, Telecommunications, Fiber optics, Orthogonal frequency division multiplexing, Prototyping, Channel projecting optics
This paper describes the operation of the prototype of the Radio-over-Fiber telecommunication system with the generation of OAM signals in the W-band. A method for generation both a radio and an optical OAM signal in RoF is proposed, a method for useful information transmission using OFDM technology in the considered system is described, an approach to converting optical vortexes into the radio domain is proposed, and a feedback channel simulation in RoF systems using OAM signals is carried out.
In this paper, an alternative fiber-optic method for forming vortex modes based on a chiral (twisted) microstructured fiber is proposed. This fiber can be considered as a ring-core fiber with ring core formed by capillaries. Besides, optical fibers design for transmitting optical vortexes over long distances. i.e. a vortex-maintaining fiber is also proposed. This fiber is a multimode fiber with an extremely large core. A comparison of the different types of vortex generation and vortex-maintaining fibers is also given. Both proposed fibers can be used in Radio over Fiber systems applying vortex beams.
We propose and fabricate pilot lengths of two type microstructured optical fibers with chirality, induced during the drawing process under 10 and 66 revolutions per meter. The first one is microstructured fiber with geometry providing quasi-ring radial mode field distribution. So it imitates ring-core optical fiber properties by special formation of designed 2D-periodic structure. The second is fiber with hexagonal geometry and shifted core in relation to central axe. The work presents results of numerical analysis of fabricated samples, performed by rigorous numerical method. Here initial data were set via manufactured optical fiber end face images. We also reports some results of far field laser beam profile images, measured at the output of described fiber samples under laser source excitation at wavelength 1550 nm.
KEYWORDS: Orthogonal frequency division multiplexing, Signal attenuation, Modulation, Radio over Fiber, Signal to noise ratio, Signal processing, Non-line-of-sight propagation, Telecommunications, Atmospheric propagation, Systems modeling
In this paper we present advanced modulation and coding techniques for telecommunication systems based on Orthogonal Frequency Division Multiplexing and Radio-over-fiber technologies operating in the subteraherz frequency range 75-110 GHz (W-band). The scheme for the Radio-over-fiber communication system based on full-optical frequency upconversion, and detailed description of the W-band wireless channel are presented. As a result, the main factors affecting the quality of the transmitted radio signal are identified, against which the developed modulation formats are aimed. Improving the efficiency of the Radio-over-fiber system is achieved in two stages: by reducing the interchannel interference due to the windowing of received signal, and reducing the peak-to-average power ratio by precoding the subcarrier frequencies of the group spectrum; by increasing the signal-to-noise ratio when using constellation rotation technique. Obtained simulation results showed that application of the proposed advanced modulation and precoding techniques in Radio-over-fiber systems provides the improvement of energy efficiency and noise immunity.
In this article the propagation of soliton-like vortexes in the optical segment of Radio-over-Fiber system is considered. The approach is based on solution of nonlinear Schrödinger equation (NSE) for Kerr-type nonlinear medium. A numerical NSE solution for vortex solitons was obtained; simulation of the soliton-like vortexes propagation over an optical fiber was performed. Moreover, a phase-amplitude filter forming optical signals with a set orbital angular momentum state and polarization conserving during propagation through an optical fiber was simulated. The calculation of amplitude-phase filter was conducted based on spinor representation of Maxwell’s equations.
In this paper coupling of linearly polarized (LP) modes (forming an orthogonal basis of mode division multiplexing systems, MDM) caused by fiber cracks and cleavages is considered. Fiber cracks as well as bends and curves are unavoidable deformations and defects appearing during fiber exploitation. The physical origin of these cracks may vary: from technological flaws to exploitation factors including different stresses, temperature deviations, curves, longitudinal tension, pressure etc. The most common effect that cracks provide to classical multiplexed signals (WDM, FDM) is additional losses and reflection which can be measured by conventional reflectometer but it can be shown that any crack is itself also an additional transversal refraction index perturbation leading to the mode coupling and therefore to excitation of spurious modes. Consequently, in terms of MDM systems mode coupling becomes one of the important factors limiting MDM systems performance, so investigation of non-avoidable factors influence is a significant task: this aspect is a key factor of MDM systems implementation. Coupling of LP modes due propagation through fiber Bragg gratings (FBG) is also considered. FBG are widely used in a lot of telecom applications including PONs, AONs, DWDM systems, etc., so investigation of FBG influence on mode coupling is significant due to commercialization and establishment of MDM-systems.
Apodization of the fiber Bragg grating (FBG) is a smooth change in the modulation amplitude and alignment of the average value of the induced refractive index along the FBG. Apodization helps to reduce the lateral peaks that are present in the spectra of homogeneous fiber Bragg gratings. In this paper different apodization functions are considered and efficiency comparison of these functions is given.
In this article the basic information about the whispering gallery modes (WGM) concerning questions of mathematical description, properties of whispering gallery resonators (WGR), methods of radiation coupling into resonators, resonators manufacture methods, and possible applications in the field of optical communication systems is considered. A brief history of WGM discovery is presented, and the main properties and characteristics of such resonators and modes are discussed. The main goal of this work is to survey the field of WG modes that is becoming more and more attractive due to their interesting and exciting properties with accordance to possible applications in passive optical components development as well as in design of active components such as lasers and modulators.
In this paper physical effects caused by macro- and micro bends of optical fiber including additional mode-dependent loss, mode coupling and spurious mode excitation in fiber MDM-system are considered. The effects described below can dramatically decrease capacity and maximum data rate in such systems because of inevitability of fiber bends due to system exploitation thus making MDM-system commercialization much more difficult and expensive. Mathematical approach used to describe these effects and applied in the simulation model is based on well- known refractive index profile approximation [1] of bent step-index fibers and mathematical field coupling model [8].
In this paper we introduce a novel method for mode-coupling compensation in MDM systems based on the adaptive optics. This approach is intended to minimize significantly the computational complexity required for digital signal processing, because only computation of diffraction optical element transmission function is performed and no real time signal processing is required to compensate for intermodal interference. Therefore, existing challenges of MIMO MDM systems, such as DSP performance limits and increasing power consumption, might be overcome.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.