We report on the laser cutting of carbon fiber reinforced thermo-plastics (CFRTP) with a cw IR fiber laser (single-mode
fiber laser, average power: 350 W). CFRTP is a high strength composite material with a lightweight, and is increasingly
being used various applications. A well-defined cutting of CFRTP which were free of debris and thermal-damages
around the grooves, were performed by the laser irradiation with a fast beam galvanometer scanning on a multiple-scanpass
method.
We report on the laser cutting of carbon fiber reinforced plastics (CFRP) with a cw IR fiber laser (average power: 1kW). CFRP is a high strength composite material with a lightweight, and is increasingly being used various applications. A well-defined cutting of CFRP which were free of debris and thermal-damages around the grooves, were performed by the laser irradiation with a fast beam galvanometer scanning on a multiple-scan-pass method.
We examined the thermal crystallization of deposited films made of 2,5-bis(4-biphenylyl)thiophene (BP1T) and
1,4-bis(5-phenylthiophen-2-yl)benzene (AC5), which are thiophene/phenylene co-oligomers (TPCOs). The deposited films
of both BP1T and AC5 showed a microcrystalline phase, and initial microcrystals got larger 10 - 100 times with thermal
treatment. Furthermore, we measured the optical properties of microcrystals of BP1T and AC5. At the energy density
below the spontaneous amplified emission threshold, it was found that there was a big fluorescent difference between
femtosecond laser irradiation and continuous lamp irradiation.
By laser-induced backside wet etching (LIBWE), we can fabricate deep microstructures with high aspect ratios. To fabricate such
deep microstructures by means of a mask-projection system, appropriate optimization of the sample positions is indispensable to
maintain the imaging conditions of the mask-projection system at the etch front. By applying the appropriate optimization, the
trenches with homogeneous widths and high aspect ratios could be fabricated. At present, a trench with an aspect ratio of 102 (width:
9.7 μm, depth: 986 μm) was successfully prepared. When the irradiated area was gradually shifted in a direction perpendicular to the
incidence of the laser beam, inclined features could be fabricated in the deep microtrenches. The tilting angles of the features could be
can be flexibly controlled between -30° and +30° by changing the shifting speed. Moreover, the angles could be varied within a
single deep microtrench. Fabrication of deep microhole array was also demonstrated. Fabricated microholes were converted into
through holes on grinding.
By laser-induced backside wet etching (LIBWE), we can fabricate microfluidic channels on silica glasses. These channels have
smooth bottom surfaces that can be combined with various optical detection techniques. Antiresonant guided optical wave (ARGOW)
is a concept for guiding light in the system composed of a low refractive index medium surrounded by a medium with higher
refractive index. The ARGOW was examined by using the wide channels (length: 17 mm, width: 1 mm, depth: 45 μm) prepared by
LIBWE, whose bottom surface showed root-mean-square (RMS) roughness less than 100 nm. The LIBWE can fabricate deep
trenches with high aspect ratio (~57 (length: 1mm, width: 10 μm, depth: 566 μm)). By using such deep channels, ARGOW system
within a plane parallel to the top surface of glass can be fabricated. In this work, surface roughness of the sidewall of deep trenches
prepared with LIBWE was evaluated, and the possibility of utilization for guiding light is discussed.
We have investigated a one-step method to fabricate a microstructure on a silica glass plate using laser-induced backside
wet etching (LIBWE) upon irradiation with DPSS (diode-pumped solid state) lasers. Well-defined deep microtrenches
without crack formations on a fused silica glass plate were fabricated by LIBWE method. As the laser beam of DPSS
UV laser at a high repetition rate up to 5 - 100 kHz is scanned on the sample surface with the galvanometer controlled by
a computer for flexible operations, galvanometer-based point scanning system is suitable for a rapid prototyping process
according to electronic design data in the computer. The behavior of liquid ablation (explosive vaporization) was
monitored by impulse pressure detection with a fast-response piezoelectric pressure gauge. LIBWE method is suitable
for rapid prototyping and rapid manufacturing of surface microstructuing of silica glass as mask-less exposure system in
a conventional atmospheric environment.
Laser-induced formation of functional materials from glasses has a great potential for creation of monolithic and high-performance
glass-based devices, such as optical circuit and micro-TAS. We have recently developed a laser-induced
formation technique of photocatalytic titanium oxide on a UV-absorbing TiO2-SiO2- based glass surface by excimer laser
irradiation under a specific condition, which we term laser-induced superficial phase separation. The laser-induced
structure has the shape of micro-cones, growing into micro-sized network after accumulating laser pulses, which we call
TiO2 micronetwork. The TiO2 micronetwork exhibited the rutile crystalline phase and photocatalytic ability. Moreover,
the crystalline phase can be controlled from the rutile to the anatase by post-treatments. Utilizing this technique, we were
able to make a site-selective growth of TiO2 micronetworks: a microwell array and a microchannel modified with the
TiO2 network only on the bottom. This flexible formation of photocatalytic TiO2 onto a glass surface without any heat-treatments
and/or adhesives opens a new way to develop a monolithic glass device like micro-fluidics with light-catalyzed
reactions.
We printed FeSi2 micro-dot array on various kinds of substrates utilizing laser-induced forward transfer (LIFT). An
amorphous FeSi2 was deposited by sputtering on a transparent plate as a source film. A single KrF excimer laser pulse
through a mask-projection system was imaged with a small micrometer-sized grid pattern onto a film/plate interface,
resulting in the deposition of FeSi2 micro-dot array on a facing substrate with a high number density of 104 mm-2. FeSi2
in the &bgr; crystalline phase is a promising eco-friendly semiconductor because of NIR electroluminescence used for optical
networking as well as abundant components reserve on the earth and non-toxicity. However, the &bgr;-FeSi2 film fabrication
generally required high-temperature multi-processes which hamper its integration and performance reproducibility.
Using the LIFT of micro-dot array, we succeeded in room-temperature preparation of &bgr;-FeSi2. Micro-Raman
spectroscopy confirmed the &bgr; crystalline phase in the micro-dots deposited on an unheated silica glass substrate. Thus,
the LIFT is useful for integrating functional micro-dot array accompanied by the crystallization at lower temperatures.
Laser-induced backside wet etching (LIBWE) method has been developed as a technique for micromachining of
transparent materials. Such technique can be applied for fabricating microfluidic devices used as "Lab on a Chip" or
total microanalysis system (μTAS). In such devices, various functions are integrated onto one chip. Microstructure with
1μm resolution fabricated within microfluidic channels can afford additional functions to the chip. Color-encoded
microbeads with surface functional groups randomly arranged in the microstructure can be used for bioarray analyses.
We have fabricated a novel microfluidic device incorporating two-dimensional array of microbeads with 10 μm
diameter. The performance of the microfluidic bead array was confirmed by a capturing experiment of DNA.
Surface micro-structuring of silica glass plates was performed by using laser-induced backside wet etching (LIBWE) upon irradiation with a single-mode laser beam from a diode-pumped solid-state UV laser at 266 nm. We have succeeded in a well-defined micro-pattern formation without debris and microcrack formations around the etched area on the basis of galvanometer-based point scanning system with the laser beam. The behavior of liquid ablation (explosive vaporization) was monitored by impulse pressure detection with a fast-response piezoelectric pressure gauge. LIBWE method is suitable for rapid prototyping and rapid manufacturing of surface microstructuing of silica glass as mask-less exposure system in a conventional atmospheric environment.
Surface micro-structuring of silica glass plates was performed by using laser-induced backside wet etching (LIBWE) upon irradiation with a single-mode laser beam from a diode-pumped solid state UV laser at 266 nm. We have succeeded in a well-defined micro-pattern formation without debris and microcrack formations around the etched area on the basis of Galvanometer-based point scanning system with the laser beam. This method is suitable for rapid prototyping and rapid manufacturing of surface microstructuing of silica glass in a convetional atmospheric environment.
We have developed a room-temperature fabrication process for β-FeSi2 microprecipitates through the active use of droplets generated by pulsed laser deposition. The droplets generated by KrF excimer laser ablation of an α-FeSi2 metallic target were characterized by micro-Raman spectroscopy with a spatial resolution of 1 μm and X-ray diffraction measurements. As a result, it was confirmed that the micron-sized droplets precipitated as the β-FeSi2 semiconducting phase on silicon and silica glass substrates maintained even at room temperature, whereas the rest of the deposited film was amorphous. It was also found that films containing a high density of β-FeSi2 microprecipitates exhibited 1.55 μm photoluminescence at low temperature after annealing at 800°C for 6 h in an argon atmosphere.
For the application of F2 lasers to micro-/nano-fabrication including photolithography, one of the important research subjects is to eliminate the chromatic aberration, and combination of lenses made of two optical materials with different refractive indices is the effective way. However, only CaF2 is widely applied to lenses for a vacuum ultraviolet (VUV) beam, and a "second material" to be paired with CaF2 is strongly requested. Here, we examined two fluoride crystals which are transparent in the VUV region, BaF2 and LiCaAlF6 grown by the Czochralski technique, as candidates for VUV optics. We investigated the change of the VUV transmittance and the onset of optical damage of these fluoride crystals against F2 laser irradiation. These crystals showed good optical tolerance against cumulative F2 laser irradiation, and the damage threshold of LiCaAlF6 was similar to that of VUV grade CaF2 while that of BaF2 was about half of the other two fluoride crystals.
Silica glass is an important material in optics and optoelectronic devices because of its outstanding properties, such as transparence in a wide wavelength range, strong damage resistance for laser irradiation, and high chemical stability. In order to develop simpler processes of micro-fabricating silica glass using a pulsed laser, we have investigated a one-step method to microfabricate a silica glass plate using laser-induced backside wet etching (LIBWE) upon irradiation with ns-pulsed UV lasers. Two laser irradiation systems were employed for the fabrication; (1) mask projection system with a KrF excimer laser and (2) Galvanometer-based point scanning system with a single mode laser beam from a diode-pumped solid state laser at 266 nm. We have succeeded in a fine micro-fabrication of silica glass surface. In addition, a novel approach in the fabrication of microarrays of dye and protein on fused silica plates using LIBWE technique was achieved. The surace of fused silica plates was initially pre-coated using trimethoxysilane self-assembled monolayers (SAMs), then etched using the LIBWE method to obtain the desired microstructures on the plate surface. Using this technique, the SAMs on the non-irradiated areas were able to survive the LIBWE process, and were used as templates for the subsequent deposition of dye molecules, proteins, or polystyrene microbeads via chemical bonding or physical adsorption.
Surface micro-structuring of fused silica glass plates was performed by single-shot irradiation with a single-mode laser beam from a diode-pumped solid state UV laser at 355 nm. Well-defined micropattern without debris and microcrack formations around the etched area was fabricated by laser ablation with a focused laser-beam in the ambient air. The time-resolved optical emission spectra of plume were measured to elucidate the ablation behavior of silica glass induced by nanosecond-pulsed laser irradiation at 355 nm where absorption of silica glass is negligibly small. This method is suitable for rapid prototyping of surface microstructuing without a clean room environment.
Silica glass is an important material in optics and optoelectronics because of its outstanding properties, such as transparence in a wide wavelength range, strong damage resistance for laser irradiation, and high chemical stability. In order to develop simpler processes of micro-fabricating silica glass using a pulsed laser, we have investigated a one-step method to microfabricate a silica glass plate using laser-induced backside wet etching (LIBWE) upon irradiation with a ns-pulsed excimer laser. Our idea of LIBWE is based on the deposition of laser energy on the surface of silica glass using ablation of a dye solution. When the dye solution was ablated upon the laser irradiation, the etching of a surface layer was performed on the silica glass. We have succeeded in the micro-fabrication of such transparent materials as silica glass, quartz, calcium fluoride, sapphire and fluorocarbon resin. The advantages of our LIBWE method are as follows, (1) a lwo laser fluence and constant etch rate, (2) microfabrication without debris and cracks formation, (3) large area irradiation with an excimer laser beam through a mask projection, (4) simple pre/post-treatment on target substrates. This is a one-step process simpler method at ambient pressure, which would be used for mass production.
A novel approach for the fabrication of micropatterns where dye molecules can be site-selectively desposited is described. The micropatterns were fabricated on the surface of fused silica plates using the technique of laser-induced backside wet etching (LIBWE). Prior to the LIBWE process, the surface properties of the fused silica plates were modified with self-assembling trimethoxysilanes bearing functional moieties. On the non-irradiated areas, the self-assembled monolayers (SAMs) survived the LIBWE process, and the remaining SAM acted as a template for the subsequent dye deposition either with chemical bonding or physical adsorption. Site-selective dye deposition was visualized with fluorescence microscopic observation. These results are applicable for micro-fluidic reactors and chemical sensors.
The early stage of optical damae caused by F2 laser irradiation on the wide bandgap fluoride crystal, CaF2, is investigated and compared with the case of ArF laser irradiation. Besides a blue emission band due to self-trapped exciton, sharp emission lines appear and grow at a fluence of about 2 J cm-2, showing the initiation of the optical damage and growth of plume from the F2-laser-irradiated surface of CaF2. There exist cracks and melted structures on the laser-damaged surface, which are caused by thermal stress and vaporization due to laser absorption and following local heating.
Laser-induced backside wet etching of silica glass plates was performed by the excitation of a pure toluene solution with a ns-pulsed KrF excimer laser at 248 nm. Well-defined grid micropattern was fabricated without debris and microcrack around the etched area. To understand the etching mechanism, the formation and propagation of shockwave and bubble were monitored by time-resolved optical microscopy at the interface between the silica glass and the toluene solution after laser irradiation. Transient high-pressure as well as high-temperature generated by UV laser irradiation plays a key role in the etching process.
Laser-induced backside wet etching of fused silica plates using aqueous solutions of naphthalene-1,3,6-trisulfonic acid trisodium salt (Np) and pyranine (py) was performed upon KrF excimer laser irradiation at 248 nm. The two etching media show different etching behavior with changing laser fluence and medium concentrations. Well-defined line-and-space and grid micropatterns at 1 μm scale were fabricated using an aqueous solution of Np and the etched pattern was free of debris and microcracks.
Time-of-flight (TOF) mass and optical emission spectroscopies have been performed on the ablation plume from α-FeSi2 alloy target under KrF excimer laser irradiation at a fluence of 0.35-2.5J/cm2 to characterize the mass, kinetic energies and excited states of the ejected species. According to the TOF mass measurements in vacuum, the most prominent species were Si and Fe atoms and ions over the entire fluence range, in addition to Si dimer. At 0.4-0.7 J/cm2, only neutrals of Si, Fe and Si2 with the kinetic energy of around 0.2eV were observed. At the fluences above 0.7J/cm2, doubly and singly charged Si and Fe ions appeared abruptly increased their number density and kinetic energies from 6 eV at 0.7 J/cm2 to over 100 eV at 2.5 J/cm2. Consistent with the TOF mass spectra, the optical emission lines stemmed from the monatomic Si and Fe as well as Si dimer in the wavelength range of 240-800 nm in vacuum. On the other hand, we confirmed some luminescent lines appeared only in helium atmosphere of 10 Torr, suggesting the cluster formation such as FeSi.
We have investigated dynamics of ablated species in ZnO plume under ArF excimer laser irradiation with emission imaging and spectroscopy, and discussed the effect of a surrounding inert gas. Surrounding He or Ar gas strongly cools down the plume and encourages aggregation of ablated species, which is visualized by second laser irradiation to the plume.
With the widespread application of excimer lasers for micro- processing, optically transparent materials in the UV region have become more important as optical components. The transparent materials currently available commercially are silica glass and fluoride crystals, CaF2 and MgF2. The resistance of these materials against cumulative irradiation of excimer lasers is required from the viewpoint of application, and it is important to clarify the mechanisms of the optical damage on these materials. In this paper, we report the onset of laser ablation, that is, the initiation of optical breakdown and plume formation, in CaF2 crystal under cumulative irradiation of an ArF excimer laser. When the laser fluence is below the ablation threshold, a blue luminescence due to self-trapped exciton is observed from the whole laser-irradiated region. When the fluence ins increased near the threshold, successive irradiation finally cause a bright, localized luminescence due to the initiation of laser ablation. SEM images of the laser-damaged region show two features: (1) a small bump with pits of the order of 0.1 micrometers formed by UV laser absorption and following local heating, (2) small cracks with triangular fragments caused by mechanisms stress under local heating.
Laser ablation of nitrogen solid film deposited on a copper plate at 10 K was investigated by the irradiation of a picosecond UV laser at 263 nm in vacuum. Photo-dissociation of nitrogen molecule in the solid film was confirmed by the optical emissions, which were ascribed to atomic nitrogen, during the laser irradiation at the fluence of 5 J cm-2 pulse-1. This photolysis was discussed by the comparison with laser-induced breakdown of nitrogen gas. At the fluence over ca. 10 J cm-2 pulse-1, the ablation of the frozen nitrogen film was observed. Employing the ablation plume including a reactive species such as nitrogen atoms, the surface reaction of a graphite oriented pyrolytic graphite plate and silicon wafer was studied. XPS analysis indicated that nitrides were formed on the surfaces by the treatment. The ps-laser ablation of nitrogen solid film provides a novel technique for surface modification of materials.
We report the onset of plume formation and optical breakdown in a synthetic silica glass under KrF excimer laser irradiation by luminescence spectroscopy and imaging. With increasing laser fluence, bright, highly localized luminescence due to plume formation appears on the luminescence image, and sharp lines due to Si atom fluorescence appear in the 200-300 nm region on the luminescence spectra. The SEM images on the laser-damaged region show typically two structures: (1) many small holes of the order of 1 micrometer suggesting localized vaporization, and (2) large craters of 10-100 micrometers due to spallation. The large craters have irregular shapes consistent with fracture often seen in amorphous materials.
An investigation on the laser ablative shaping (LAS) of the quartz glass has been made experimentally. F2 laser was used as the laser light source for efficient ablation of quartz material. The output beam of F2 laser was focused on to the surface of quartz plate. The ablation rate was about 10 micron m/pulse at the irradiation fluence of 2 J/cm2. A uniform ablation of quartz plate has been demonstrated using F2 laser. The waveform of incident and transmitted laser light was measured by high speed photo-tubes to observe the time dependence of the absorption. The measured waveform indicates that the absorption was small at the leading edge of the laser pulse, and a strong absorption was induced at the end of laser pulse due to the excited state absorption. These phenomena are quite similar to both in F2 and ArF laser light. We have developed a simple model in which the instantaneous absorption is proportional to the absorbed energy prior to the moment. The calculated absorption was in good agreement with the measured wave- form. The change of transmittance in UV and VUV region was measured after the irradiation of F2 laser for samples of different concentrations of impurities.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.